Crescendo Evolution W1S3 is a 3 way speaker that sounds natural with minimal distortion and works in the range of 50 Watt – 100 Watt. The appearance is nice looking and small so it can fit almost any car.

• Crescendo Evolution W1S3 Active- $690.00
• Crescendo Evolution W1S3 Semi Passive- $950.00
• Crescendo Evolution W1S3 Full-Passive- $1060.00

Some modern features of Evolution W1S3 as follows:
Tweeter

• Tweeter size is 25 mm (1”) with soft fabric dome cone for the most neutral sound. Tweeter motor system consist of  neodymium magnet, which is 8 times more powerful than conventional Ferrite magnet, as well as voice coil made from lightweight CCAW (Copper Clad Aluminium Wire) thus the sound reproduction is detail and dynamic.
• Tweeter has ventilation at the back to reduce heavy wave density behind the cone and furthermore it has concave pole piece that acts as a diffuser to produce sound with minimal distortion.
• Tweeter is equipped with tuning cable which is custom designed to optimize tweeter performance.

Midrange

• Midrange size is 98 mm (3.85 inch) with Polypropylene cone as the best combination of performance and price. Midrange motor system consist of 12 mm height, 65 mm diameter Ferrite magnet as well as 20mm lightweight CCAW thus the sound reproduction is clean and dynamic.
• Midrange uses short chassis and its parameter is designed to work optimal at very small sealed box so it can be installed in almost any car.

Midwoofer

• Midwoofer size is 165 mm (6.5 inch)with Polypropylene cone as the best combination of performance and price. Midwoofer motor system consist of 15 mm height, 90 mm diameter Ferrite magnet as well as 25mm lightweight CCAW winded on Kapton former thus the sound reproduction is powerful and dynamic.
• Midwoofer has ventilation at the back and also at the chassis to reduce heavy wave density behind the cone so that the sound reproduction has very minimal distortion.

Passive Crossover

• Passive Crossover is seriously designed inside the car thus customer will hear the same sound as Crescendo designer. Tweeter level adjuster uses L-Pad design concept which is more costly but also more superior to single resistor in terms of consistency in reducing the level throughout whole frequency.

Passive Crossover is available in 2 version:

• W1X3 is 3 way passive crossover for tweeter, midrange, and midwoofer all together, consist of 17 components with 3 tweeter level adjustment, 2 midrange level adjustment, and 2 midwoofer level adjustment. Using this passive crossover W1X3, only 2 channel of amplifier is needed and without the need of additional active crossover or Digital Signal Processor.
• W1X2 is 2 way passive crossover for tweeter and midrange, consist of  11 components with 3 tweeter level adjustment.Using this passive crossover W1X2, minimum of 4 channel amplifier is needed and also active crossover or Digital Signal Processor to cross-over midrange and midwoofer.

Technical Data

• Minimum impedance: 4 Ohm
• Frequency response: 56 Hz – 20 kHz
• Power Demand: 50 – 100 Watts
• Cosmetic appearance: Black and White
• Package accessories: Nickel plated screws
• Tweeter cone size: 25 mm
• Tweeter cone material: Soft fabric dome
• Tweeter magnet: Neodymium
• Tweeter motor design: Concave pole, Underhung
• Tweeter chassis: ABS plastic, Patented design
• Tweeter accessories: Custom tuned silver plated copper 4N cable
• Midrange size: 3 inch
• Midrange voice coil: 20 mm, CCAW
• Midrange cone material: Polypropylene
• Midrange surround material: Butyl rubber
• Midrange magnet: D = 65 mm, H = 12 mm, Ferrite
• Midrange motor design: Overhung
• Midrange chassis: Stamped steel
• (Mid)woofer size: 165 mm (6.5 inch)
• (Mid)woofer voice coil: 2 layer, 25 mm, CCAW
• (Mid)woofer cone material: Polypropylene
• (Mid)woofer surround material: Butyl rubber
• (Mid)woofer magnet: 90 x 15 mm, Ferrite
• (Mid)woofer motor design: Overhung
• (Mid)woofer chassis: Ported, Stamped steel 0.7mm

Crescendo Evolution W1S3 is a 3 way speaker that sounds natural with minimal distortion and works in the range of 50 Watt – 100 Watt. The appearance is nice looking and small so it can fit almost any car.

• Crescendo Evolution W1S3 Active- $690.00
• Crescendo Evolution W1S3 Semi Passive- $950.00
• Crescendo Evolution W1S3 Full-Passive- $1060.00

Some modern features of Evolution W1S3 as follows:
Tweeter

• Tweeter size is 25 mm (1”) with soft fabric dome cone for the most neutral sound. Tweeter motor system consist of  neodymium magnet, which is 8 times more powerful than conventional Ferrite magnet, as well as voice coil made from lightweight CCAW (Copper Clad Aluminium Wire) thus the sound reproduction is detail and dynamic.
• Tweeter has ventilation at the back to reduce heavy wave density behind the cone and furthermore it has concave pole piece that acts as a diffuser to produce sound with minimal distortion.
• Tweeter is equipped with tuning cable which is custom designed to optimize tweeter performance.

Midrange

• Midrange size is 98 mm (3.85 inch) with Polypropylene cone as the best combination of performance and price. Midrange motor system consist of 12 mm height, 65 mm diameter Ferrite magnet as well as 20mm lightweight CCAW thus the sound reproduction is clean and dynamic.
• Midrange uses short chassis and its parameter is designed to work optimal at very small sealed box so it can be installed in almost any car.

Midwoofer

• Midwoofer size is 165 mm (6.5 inch)with Polypropylene cone as the best combination of performance and price. Midwoofer motor system consist of 15 mm height, 90 mm diameter Ferrite magnet as well as 25mm lightweight CCAW winded on Kapton former thus the sound reproduction is powerful and dynamic.
• Midwoofer has ventilation at the back and also at the chassis to reduce heavy wave density behind the cone so that the sound reproduction has very minimal distortion.

Passive Crossover

• Passive Crossover is seriously designed inside the car thus customer will hear the same sound as Crescendo designer. Tweeter level adjuster uses L-Pad design concept which is more costly but also more superior to single resistor in terms of consistency in reducing the level throughout whole frequency.

Passive Crossover is available in 2 version:

• W1X3 is 3 way passive crossover for tweeter, midrange, and midwoofer all together, consist of 17 components with 3 tweeter level adjustment, 2 midrange level adjustment, and 2 midwoofer level adjustment. Using this passive crossover W1X3, only 2 channel of amplifier is needed and without the need of additional active crossover or Digital Signal Processor.
• W1X2 is 2 way passive crossover for tweeter and midrange, consist of  11 components with 3 tweeter level adjustment.Using this passive crossover W1X2, minimum of 4 channel amplifier is needed and also active crossover or Digital Signal Processor to cross-over midrange and midwoofer.

Technical Data

• Minimum impedance: 4 Ohm
• Frequency response: 56 Hz – 20 kHz
• Power Demand: 50 – 100 Watts
• Cosmetic appearance: Black and White
• Package accessories: Nickel plated screws
• Tweeter cone size: 25 mm
• Tweeter cone material: Soft fabric dome
• Tweeter magnet: Neodymium
• Tweeter motor design: Concave pole, Underhung
• Tweeter chassis: ABS plastic, Patented design
• Tweeter accessories: Custom tuned silver plated copper 4N cable
• Midrange size: 3 inch
• Midrange voice coil: 20 mm, CCAW
• Midrange cone material: Polypropylene
• Midrange surround material: Butyl rubber
• Midrange magnet: D = 65 mm, H = 12 mm, Ferrite
• Midrange motor design: Overhung
• Midrange chassis: Stamped steel
• (Mid)woofer size: 165 mm (6.5 inch)
• (Mid)woofer voice coil: 2 layer, 25 mm, CCAW
• (Mid)woofer cone material: Polypropylene
• (Mid)woofer surround material: Butyl rubber
• (Mid)woofer magnet: 90 x 15 mm, Ferrite
• (Mid)woofer motor design: Overhung
• (Mid)woofer chassis: Ported, Stamped steel 0.7mm